GEARWRENCH Indexing Pry Bars

1. i have a indexing prybar, and im pretty sure its the same brand even but mine is different. the handel end on mine is not pointed, its blunt to hit with a hammer. and the indexing head also has 2 flat spots to hit with a hammer.

2. The big one (29 & 1/2") looks as though it could also hang on a belt loop (D cell) Mag-Lite holder & be used as a permanent intruder deterrent.

3. I've got one but mine does not extend. 2 foot version and it is very nice to have.

4. Friggin awesome

5. Awesome tools

6. These are one of those things you wish you had invented. These are awesome pry bars as a millwright we use these all the time in the steel mill.
   They take the abuse well .
   Overall gear wrench tools are pretty descent.

7. I've had these exact tools for a few years, not sure if they're gear wrench but they are great. The telescoping ones flex quite far when fully extended, but I have yet to bend one.

8. They need a pointy end on the handle for aligning bolt holes…

9. Funny, just bought one too, along with a heel pry bar set (aka Ladyslipper or Ladysmith). Need to pry some tapered bearing races from a trans in a week. We'll see which works better!

10. I needed one of these to pop out a CV shaft on a Polaris ranger. Tight and odd angle

11. Oh man, the valve cover seal removal. Holy cow, super easy, barely an inconvenience.

12. 😛

13. Gearwrench is the way to go

14. It's too bad the butt end of them isn't pointy like your old one for lining up bolt holes.

15. Not a big fan of GearWrench tools. GW has some decent stuff but most is CCP garbage. I have a set of the original GearWrench and served me well over the last 15 + years. Current selection quality is horrible. Capri and Tekton are far better for around the same price.

16. Gosh those would be cool tools to have but I’m Covid rich so no bueno

17. I love learning about tools

18. Umm I probably should say this publicly however I had the unfortunate circumstance of having to spend a week in the county jail, and on these new tablets they were handing out, they had like 30+ of your videos set up as a course on there. Needless to say I learned quite a bit about brakes and HVAC systems and “what’s the noise” videos. All very entertaining and informative! I’m most definitely a fan. Not sure when the videos in the course were from, I’m thinking at least 10 years ago. There was no mention of YouTube and your production quality has gone up significantly! (Remember an early video where you wrote “FOCUS!! Sorry!!” On the screen? Hahaha dude, this is great stuff, and I appreciate your work!

19. What about the durability? I can't imagine that the mechanism will hold up to prying. "Review" .. is not a review but a plug for your sponsor.

20. Awesome addition for the toolbox, but unfortunately they are quite fragile over the static heelbar/ladyslipper.
    Though in heavy equipment you do break quite a few pry-bars and sledgehammers.

21. Wouldn't last ten seconds if left out at my job. People don't "borrow" they flat out steal.

22. Eric you look like a kid with a new toy @ Christmas time. But you are right they are AWSOME

23. id gladly pay $4.99 for the small one

24. The sounds looks like GLOCK hand gun 😂

25. Now if only Andrew Camarata could make his yellow one indexable….. hmmmm…

26. I like the slots on the heads of the bigger pry bars. I bet they grab into what you're prying against to keep from slipping.

27. How strong are the weakest points is the question

28. Doesn't take much to excite You.
    But I understand…
    You should start Drinking Immediately!
    🤔🤓😉👍🇱🇷🇱🇷

29. Thanks for the review. I could used these years ago.

30. 3:26 what my wife said last night

31. Wow I’ve been watching your YouTube since middle school !
    I love your videos
    You helped me save a lot of money

Comments are closed.