Chevy 350 TBI Built In The Backyard with Hand Tools? Challenge Accepted! – Engine Power S8, E17

1. SAMTech here I come…

2. What power did it make?

3. Eating pizza and spraying paint. That's so hillbilly.

4. The more I watch you two the more you crack me up, great team!

5. How did you wire in your wiring harness for the efi to turn key to activate fuel pressure regulator thanks

6. When you got that engine out of the bed of the truck it didnt have a crank bolt in the balancer but after you reinstalled the balancer there was a bolt in it. Anyway to get that balancer bolt part number i have the same 90s tbi engine and cant find a balancer bolt that is long enough for the life of me.

7. What does cleaning all the carbon build up do I mean obviously it’s a good thing to do but what does it do sure it might be a dumb question

8. Well done 👍

9. 4 bolt main on a tbi?

10. 500 lift on stock tbi heads?

11. I always wanted to build a small block Chevy. Too old now, but this was almost as good.

12. Pat is the best! 👍👍👍

13. What’s the quince on them heads

14. I like to see the dyno numbers

15. From stock Rochester TBI to Demon Carburetor.

16. Don't use the ports to pry your heads off! There are several other ways to do it, especially if you plan on reusing them. Real gearheads know this. You are risking more work and more money for laziness

17. Already been rebuilt 2k miles ago!!? Crank and rods had clevite oversized bearings!??

18. I wish they would have put it a dyno to see the HP

19. These friggin doofises are the best yu ppl @ hotrod can come up wth uh, really!?

20. Filthie frank reference

21. Frankie went to UNOH, 100%, no further investigating needed

22. Thats as cool and REALISTIC VIDEO AS IT GETS!!!! thanks for sharing!!

23. I pulled an engine one time with some friends of mine with a 6 x 6 Beam on either side of the car somebody got a hold of the beam and we picked up the engine and we pulled it out set it on the ground then proceeded to rebuild it well tear it down in a wheelbarrow set the block off to be cleaned and honed sent the heads off to be redone got everything back put the engine back together put it in the car the same way with a 6 by 6 across the front of the car hooked it all up got it running on a day later drove it a thousand miles

24. I miss these Simplistic push rod carberated engines . EPA killed them all. . I'm 61 and owned so many Great engines in my lifetime. I've personally owned 34 vehicles from the big 3. All had Legendary Bulletproof engines. Never had a motor blown with my anal Maintenance. What a Great video. Thanks for the Memories.

25. Seen your most recent vid I had to scroll to the start of your success and man if you want to be friends I got unmolested 06 DMax And a 87 Lincoln Town car. We can do dumb shit to and sell put a few in my pocket and a lot in yours

26. Crankshaft kits come with matched bearings. Unless you really feel anal about clearances you won't be able to change, just run it as is.

27. Pat was shopping in the kids section for that shirt 😂

28. When y'all put the heads back on the backyard 350 build ,did you take the heads and have them worked or did you just check them with a straight edge and go back with them.

29. I'm from Canada and no auto zone here so what's the best store in Canada

30. That thing will do another 300 thousand miles easily.

31. Was there ever a dyno test or any other follow ups on this combo? Anybody know?

32. what was the oil reassure???

33. Очень интересно смотреть

34. Throw them pistons and cr in some purple power and let em sit. It'll eat all that crap off without scrubing em. Doesn't take very long either

35. Nooooooo, not a dingle ball 🤦‍♂️😂

36. Waste of time junk

37. I built most of my engines in the drive way or back yard with limited tools

38. Not free tools have to buy them the return them and not evwryone can afford to borrow a four hundred dollar tool, this page is a joke and you guy have gotten worse since your off tv

39. Pat and Frankie entertain me so much. Love the new crew.

Comments are closed.