5 Things You Must Do When Installing an Automatic Transmission

1. انت اكتر ميكانيكي محترف شفته و ان سعيد لعودتك من جديد شكرا شكرا

2. Glad to see you back online.
   I'd say #6, once the transmission is installed, push the torque converter fully into the transmission and make sure you've got clearance between the bolt hole flanges on the converter and the flex plate, usually .080-.100".
   If there's not any, something's not right. Find out what and fix it. See your #3 and #5.

3. what happen to the monster transmission ?

4. Thanks Eric 👍🏽

5. Thanks Eric. So glad you’re still staying dirty ! Hope all is going well for you. Your expertise and understanding are extremely appreciated.

6. Man those are golden rules! Thanks Eric for sharing them and I am glad to see you in the platform again!

7. How often should xmsn fluid be changed? I had mine replaced about two years ago; is it necessary to go back to the place of installation for fluid changes?

8. 👍🙂

9. Thanks Eric! So great to see you back in action!!

10. Great video

11. Thanks for the reminders. It's easy to skip those steps.

12. Good to see you back

13. ❤❤❤👍

14. Good to see you posting videos again!

15. Let's hope it never comes to this.. 🤮

16. Hey! New videos. One of my favorite YouTuber car dooders back with a new post. Great!

17. You missed out the mug of coffee or tea to keep the brain properly saturated and it gives you time to check what you have done and ready for the next step.

    O.k I'm a " Tea A Holic " 😀

18. Greetings Eric. Good to see you again.
    How goes the hunt for a new shop?

19. ETCG inspired me to make my own transmission repair. https://www.youtube.com/watch?v=g4_-0cXUQtA

20. Hola Eric! Glad to see ya again!

    I have that exact transmission jack. So glad I got it. Invaluable when removing/installing a TR3650 in an '06 Mustang lemme tell ya. 45 degree spin and 30 degree tail down orientation is kind of a thing with that due to Reasons(tm). :p

21. So glad to see you Eric😍
    Please share more video's, we really Miss you on YouTube😍

22. That's a hell of a fart at the outro. What the hell did you eat to do that?

23. Always good to see you Eric.
    Some sound advice.
    Thanks for sharing ✌️ Peace from Melbourne Australia.

24. Welcome back….Long time no see

25. Man i just looking for a video of this from you when i was installing mine on my 85 S10 couple days ago and ones I watched of others on YouTube didn't really give me what I wanted like you did but I pretty much did everything like u said however I could barley get maybe…. 1 quart of fluid in the torque converter and could not figure out why but I guess it's better than nothing at all .

    Mines a stock application for transmission side . The 700r4 but 60degree style so hopefully everything should work just fine. The spacing between the flexplate and converter has me a little concerned there's a gap but what I have seen that's normal but shouldn't be to much tho however the old engine and flexplate did not have any space or that much but I also put in a New T-Q at the same time I did my engine because the old T-Q was not locking up right it would lockup to early or sometimes hit hard if going down a hill and I didn't have my foot on gas just odd .

26. We missed you!

27. I've made the mistake of not fully seating a torque converter.

    Had to pull the 4L60 out of my mom's Caprice to do a rear main. Slipped the tc off to do a quick inspection of the front seals and gaskets on the trans. Everything's hunky dory so I put tc back on. I've done this on TH350s and ST300s before. Turned it some… clunk. Turned it some more…. clunk. Good enough.

    Went to reinstall the trans and the tc was hitting the flex plate before the bell housing was fully seated. After some cursing and head scratching and my dad asking me what's wrong, I pulled it back out. Turned the tc some more… and a third clunk. Felt like an idiot.

    "Don't tell mom."

    "Tell her what?"

    Dad and I make a good team.

28. Installing transmissions is no longer a diy job. Might have to be programmed on 07-09 and up.

    If I didn’t have a lift and transmission jack and shop at home, it never was a good idea to install transmissions at home anyway.

    Not saying it can’t be done, but most people should avoid these types of repairs. Even on those older cars and trucks, there are rusted exhaust bolts and all sorts of issues you run into. Today transmissions have modules and are electronic controlled!

    You can install a brand new transmission in a car or truck today and if you don’t have it programmed, you’re just gone burn up your brand new transmission! They probably not going to warranty it.

    A Mechanic gets out of this industry for a few years, everything has changed – and not for the better!

29. Really nice tips for future reference, hope you get a shop soon or do what you dream of but thanks for sharing man 🎉

30. You’re back!

31. Very important info. Always like to see Dad's Truck.

32. Be safe,have fun,stay dirty
    Much appreciated gentleman

Comments are closed.