BRZ Resurrection Pt 18 – DIY Air Intake

1. I know it's an old video but the crack will keep spreading. He needs to drill the end of the crack and then aluminium weld or each time it's fixed it will spread further.

2. Cold air intakes should be lower to the ground to avoid the engine bay heat. I was following along thinking you'd use the entire pipe to point your filter down towards the bottom of the engine but you cut it in half instead? Now you're definitely going to pull in the hotter air.

3. I'm surprised you didn't just remove all the stock plastic intake tubing and try and attach the air intake pipe straight to the throttle body.

4. hi mate. you need to buy a quality holesaw set

5. Loving the videos man, came for the BMW stayed for all the other stuff and that your in portland (im in Vancouver) Keep up the good work dude! I know im several months late but congrats on the shop, so jealous lol.

6. holyshet how many pt is this 30, 100,1,0000000000

7. "ratcheting strap type thing" It's called a hose clamp 😛 keep up the awesome vids, and please get more shirts!

8. 7:24 No, that's a ram air intake. A cold air intake diverts the filter to the wheel well, or other location, to suck in colder air.

   In the BRZ's case, the filter gets moved to in front of the radiator. Outside of the engine bay.

9. Car dolly's would be great for you guys garage. Just dont get the harbor freight ones unless you want to have to modify the by putting bearings in the rollers.

10. just make a hole in the hood for the cold air intake.

11. it's true though, lots of forums recommend the factory airbox and aftermarket intakes only if you want the sound it makes.

12. when I put it between both pieces than clamp it down…

13. do you still have the subi for sale?

14. Harbor freight is having a huge sale on vehicle wheel dollies

15. you by yourself pulling off this channel and all those builds. Good job, keep it going!

16. i am binge wachting your brz videos they are sooo good

17. MCM !

18. Hey small tip,
    that beeping you got when you steped out of the car is caused by the keyless system.
    On our own subaru it happens when you let the car running, step out of it with the key in your pocket and close the door. It just freaks out until you put that damn key back in the car 😀 It also happens if you let the ignition on, and close the door without sitting inside of the car 🙂
    Maby that helps reducing problems, because that beeping is not actually a problem, its intended 😛
    Keep up the good work guys!

19. who laughed after he said we were trying to Austin power that thing.

20. how did you got into mechanic?

21. Solder should be fine…jb wield should be fine too

22. The plumbing term for that is called reaming the edges of the pipe

23. i love all your videos will you please reference MAF for a 97 acura ingetra

24. Fuck dude how much time and money have you spent on this car
    all i'm saying you could have bought a 2JZ and swap in less time

25. At 10:50, did anybody else think they had stumbled into a Subaruwrxfan video? lol Joking aside though, this is one of my new favorite channels. I can't wait to see these two BRZ's when they're done.

26. is it automatic trans?

27. nice mcm plug good work my friend

28. damn, just realised that uhaul stands for you haul… .'

29. damn, just realised that uhaul stands for you haul… .'

30. Beware headphone users at 5:05 my ears nearly started to bleed.

31. Do you not have winter tires in the US? Doesn't it regularly snow in Oregon? Here in Norway all cars have at least one set of summer tires and one set of winter tires.

32. I agree with Lee Forget about putting the JB weld between the parts…then maybe around it for some extra hold.

33. Tip for you B is for Build:
    When mixing compounds like epoxy or JB Weld mix on a surface that doesn't absorb water like glass (plastic works but only thick stuff as the heat from the curing process can make a mess of the thin stuff). This will give you more working time as moisture isn't being drawn out from your compound and into your mixing surface.

34. v.v Still haven't received my keytag..

35. Moving the plan B brz was as easy as getting the car out, and coming in in reverse doing as if you were parallel parking. Just imagine the walls are cars.

36. Ditch the JB weld and get yourself some epoxy intended for bonding metals. 3M and Loctite make a wide variety of products. To use many of the professional grade epoxies you'll want a MixPac DMA50, epoxy in cartridge form and the matching static mixing tube. No more mixing goop on paper. Just point and click click click out comes perfectly mixed epoxy. All sorts of epoxies are out there for various aerospace and automotive applications.

Comments are closed.