Assessing The Damage From The Massive Wheelie

1. How much is a run on the dyno?🤣 2 birds with one stone. Dyno test my Odyssey build when its finally finished and meet the dream team over here!

2. Add bumpstop packers easy job zero arch work needed

3. Love the brown on the cummins

4. One of those "prepare for the worst, hope for the best" moments, boi u got luckyyyy

5. Wheelie bar.

6. The tires hitting the inner fender saved it from more damage. Sick wheelie Kyle!

7. This must be why Cleetus and the guys always bolt check their cars before running them.

8. The oval hole in the strut is supposed to be there. Thats the camber adjustment provision provided by Toyota and the aftermarket. Just make sure they are tight with fine thread bolts. A little loc tite maybe.

9. rally coils

10. Please tell me the red MR2 isn’t outside in the snow with that brand new paint.

11. Or just get some wheelie bars and call it a day 😊

12. Send me the motor put of the hatch when you give her a new heart transplant 🤘🤷‍♂️

13. I like to put a H22 H22 Turbo and my Dodge Dart

14. Probably ideal you get the car corner balanced for race weight and driver in the seat . Your heights gonna change on each aide to get it all even

15. MR2 needs wheelie bars 💪

16. Are you sure the lift and concrete is perfectly level? Does the car sit perfectly level?
    You should really be measuring the suspension not from the tire to the floor

17. Why and the hell would u put the same thing on that’s costing money the flex plate is going to break 2 years and a day and then ur paying the same thing over again

18. The front knuckle has a bigger hole than the diameter of the bolt, probably not the coil over. the ride height should be adjusted on the ground to avoid variables such as the lift being uneven. Measure floor to fender

19. Maybe the floors not levelEd

20. I know from my 1st gen mr2 that some of the coils have an oval hole to account for a mid-gen suspension change. there was a mid model suspension change on the sw20s too so could be that

21. One thing I've noticed, nobody has a woman!

22. impressive it even made a stable pass after the wheelie with things out of whack like that! wow

23. Whetes the HATCH?

24. Sell it buy a ford

25. Also you can not trust the lift of the height

26. Fortune auto 500 and 510 damper kits for the RX 7 are also like The bc dampers the upper holes are slotted. I freaking hate it and am trying to have a set for my 510 dampers made without the slotted holes

27. You have the 4 scale system.. I'd adjust the suspension to be as *balanced * side to side as possible. So that might mean adding traction weights under the empty passenger seat.

28. Going to add bump stops up front and wheelie bars out back?

29. Those hoists seldom lift square. I have the same and it is often out of wack. Car weight effects the cables.
    The only way to square the car is cornerweight scales. With the car firmly on the ground.

30. Put some wheelie bars on it an be done with it.

31. Godfather pizza at the Loves in lords burg nm. I live bout 40 min away.

32. ITS CALLED AN ECCENTRIC BOLT……The offset ones for adjusting.

33. You have scales so you should corner weight it with the driver in the car. Also, maybe add some wheelie bars?

34. The big question is why does the flex plate keep braking?

35. You need to let Amillo do videos

36. Increase front damper rates to handle wheelies.

    The car needs an undertray for aero.

37. The guy in the hellcat hat always helps me when I take my truck in for service

38. #end of 2020 you should reach one mil subs

39. Wheelie bars might help. Lol I am amazed at the power ya'll get out of those little engines. You guys rock

40. BC coils come oval at the op bolt

Comments are closed.