Control Arm Bushing Replacement. This video will show you how to easily replace Upper Control Arm bushings (press the old ones out and press the new ones in with common tools). This job is fast and easy and can be done with basic hand tools and a ball joint or bushing press which you can rent for free at your local parts store.
You can also use this method to replace bushings in your leaf springs and pretty much anything that has pressed in bushings!
Get inexpensive bushings here: http://www.amazon.com/s/?_encoding=UTF8&camp=1789&creative=390957&field-keywords=control%20arm%20bushings&linkCode=ur2&rh=i%3Aaps%2Ck%3Acontrol%20arm%20bushings&tag=chri0e2-20&url=search-alias%3Daps&linkId=NIGGY4IUR24UWIAR
Here is the press kit I was using (and I like a lot): http://www.amazon.com/gp/product/B0028QGT86/ref=as_li_tl?ie=UTF8&camp=1789&creative=390957&creativeASIN=B0028QGT86&linkCode=as2&tag=chri0e2-20&linkId=HAPDN7JU74P4IVHK
How to Press a Ball Joint: https://www.youtube.com/watch?v=37NgLM4tIzw
How to Replace a Chevy Upper Control Arm: https://www.youtube.com/watch?v=aPbL9HTHZg0
How to Replace a Ford Upper Control Arm: https://www.youtube.com/watch?v=v7bOxQe_WhU
How to Replace a Lower Control Arm: https://www.youtube.com/watch?v=CmN2dRAiuj0
**If the video was helpful, remember to give it a “thumbs up” and consider subscribing. New videos every Thursday**
-Website: https://www.ChrisFixed.com
-Facebook: https://www.facebook.com/chrisfix8
-Twitter: https://twitter.com/ChrisFixed
-Instagram: https://instagram.com/chrisfixit
-Subscribe Here: http://www.youtube.com/subscription_center?add_user=paintballoo7
-YouTube Channel: https://www.youtube.com/ChrisFix
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.
How for balljoin replacement tool?
helpful
Well done! Well explained! Thank you!
Hey men, do you have a link for the ball joint press?
Cool
P11111
I failed to mention, the lower control arm is the one I'm talking about. The upper one can be done the same way depending on the vehicle and how much room you have to work. I'll start with the lower one's. You will need a jack stand to put under the frame and possibly one to go under the control arm. Sometimes just a floor jack is good enough for the control arm but other times you will need a jack stand under the end of the control arm while jacking the bushing end back up into place so you can stick the bolt in it, so to change them, you only remove the bolt to one of the bushings, and when you let the jack down, only one side comes down just enough to where you can stick your air hammer, (aka air chisel) and when you hit the trigger, it will come right out, then you put some grease around the new one including the hole, put the bushing in place and find on old socket you don't care about and put it on the bushing so you're not hammering on the bushing itself, so the socket has to be big enough to fit around the rubber so that the socket is making contact with the metal rim of the bushingsd, then hit the trigger and it will push it right back in, then all you have to do is jack the control arm back up into position and stick the bolt back through it. Then you do the other one the same way. Usually the top control arm doesn't have enough room to get your air hammer in there to push the new one back in. A cheap 15 dollar air hammer won't work but something equivalent to the $50 dollar Ingersoll Rand Model# 114GQC will do most everything up to a half ton pickup truck. When you go higher than that or anything with a higher GVWR, then you'll need a bigger air hammer just because the parts are bigger.
You're doing it the hard way. I can change out both bushings with the control arm still on the vehicle, in 10 minutes or less.
Very Danger
Am I the only one on this whole thread that noticed that when he pressed it out he broke the weld on the control arm lmao.
I love this stuff. I think "hey I can do this!" Thanks ChrisFix.
Hey Chris, I have a question for you. My mechanic is saying that I will need a whole control arm to be able to replace my Bushing on my XTS. do you think that’s true what do you think or do you think he is lying?
Chris fix is always helpful, thanks you bro
A little heat can help too.
I mean… technically you have to pay full price for the tool. If you return it you get your money back. If you don’t then it’s just yours
Pushing the bushing 😂
This should be a how not to video lmao
Awsome
chris? looks like you didn't lubricate the threads on the rented press
CHRIS U DONT HAVE A IMPACK WRENCH?
You bent the shit out of that control arm doing that, good job! Jesus… XD